The Globe and Mail

Go to the Globe and Mail homepage

Jump to main navigationJump to main content

Press release from CNW Group

Treasury Metals Drills 27 metres of 1.9 g/t Gold in Developing C Zone at Goliath

Tuesday, January 29, 2013

Treasury Metals Drills 27 metres of 1.9 g/t Gold in Developing C Zone at Goliath07:00 EST Tuesday, January 29, 2013TSX: TMLTORONTO, Jan. 29, 2013 /CNW/ - Treasury Metals Inc. is pleased to report drilling results from the C Zone of the Company's flagship Goliath Gold Project located in northwestern Ontario. The C Zone mineralisation is located approximately 30 to 50 metres adjacent to the Project's Main Zone of mineralization.These results include near surface intersections of 27 metres at 1.9 g/t Au from 51 metres depth in drill hole TL 12-295 and 12 metres at 2.2 g/t Au from 33 metres depth in Hole TL 12-293 and 3.0 metres at 9.0 g/t Au from 73 metres depth in Hole TL 12-290.  Drill hole TL-295 is interpreted to be the up dip extension traced to the surface of the newly discovered high grade shoot of the C Zone that was previously reported in re-entry drill hole TL-164RE on December 11, 2012. A re-entry hole is where Treasury has re-interpreted the geology and concluded that certain drill holes completed by the previous operator need to be extended in length in order to thoroughly test the project's mineralisation. This program of extending drill hole depths has led to several new mineralised zones being discovered, including 1.5 metres at 15.7 g/t Au in Hole TL148-12RE and 8.3 metres at 1.0 g/t Au in TL227-12RE and 17.1 metres at 5.9 g/t Au in earlier reported drillhole TL-164RE.These recent results are considered significant as they represent the first high-grade gold intersections that are coming together as an ore shoot within the project's sparsely drilled C Zone. They occur near surface and could represent a significant increase to the current open pit mine shells and the mineable ounces within them. These C Zone results have potential to reduce the overall waste to ore stripping ratios, especially in the Eastern section of the deposit.Drilling continues to delineate and infill the drilling pattern on the Project's C Zone which covers an area measuring approximately 1.2 km in strike length and to a depth of 200 metres as the program is focused primarily on near surface resources. This drilling program is on-going and as of today there are still some 12 holes awaiting assays.Treasury Metals' President and Chief Executive Officer Martin Walter commented: "We are certainly excited about these new intersections as they occur in areas with relatively little past drilling. This new drilling in the C Zone will have a positive impact on the proposed open pit economics which are already robust based on our Preliminary Economic Assessment that was published in July of 2012. The project has good grade, reasonable CAPEX and is located right here in Ontario surrounded by infrastructure. This makes for good business sense," said Martin Walter. Table of C Zone Drill Results:                                    Drill Hole      From (m)      To (m)      *Interval (m)      Au (g/t)      CommentsTL148-12RE      201.0      202.5      1.5      15.7      Re-entered Teck drill holeTL225-12RE      151.5      159.0      7.5      0.4      Re-entered Teck drill holeTL226-12RE      148.0      152.5      4.5      0.5      Re-entered Teck drill holeTL227-12RE      161.0      169.3      8.3      1.0      Re-entered Teck drill holeTL230-12RE      166.4      167.1      0.7      11.6      Re-entered Teck drill holeTL238-12RE      217.5      219.0      1.5      0.5      Re-entered Teck drill holeTL242-12RE      211.9      213.7      1.8      5.2      Re-entered Teck drill holeTL0826-12RE      178.0      179.0      1.0      1.2      Re-entered TML drill holeTL12-281      355.6      360.5      4.9      1.5       TL12-283      476.9      479.9      3.0      0.9       TL12-284      417.9      418.9      1.0      12.9       TL12-285      482.0      484.0      2.0      2.2       TL12-286      521.1      522.6      1.5      1.2       TL12-287      468.9      471.0      2.1      0.5       TL12-288      42.0      43.1      1.1      0.8       TL12-289      55.0      58.0      3.0      1.4       TL12-290      73.6      76.6      3.0      9.0       TL12-291      42.5      43.5      1.0      1.1       TL12-292      94.5      102.0      7.5      1.0       TL12-293      33.2      45.9      12.7      2.2       TL12-294      76.0      81.0      5.0      1.7       TL12-295      51.5      78.5      27.0      1.9       *Intervals do not necessarily indicate true widths. See attached map for drillhole locations. All depths and assays rounded to one decimalplace.  Typical sample interval approximately 1m; weighted averages use 0.3 g/t Au cut-off except for 'included' higher grade sections. Technical information in this press release has been reviewed and approved by Mr. John J. Chulick, a consulting geologist registered in the State of California and Mark Wheeler, P. Eng., Senior Mining Engineer, who are both Qualified Persons for the Goliath Gold Project under the definitions established by National Instrument 43-101.To view further details about the Goliath Project, an updated C Zone and Main Zone long section, please visit the Company's website at Assurance and Quality ControlThe Company has a quality assurance and quality control (QA/QC) program to ensure sampling and analysis of all exploration work is conducted in accordance with the CIM Exploration Best Practices Guidelines. The drill core is sawn in half with one-half of the core sample shipped to Accurassay Laboratories in Thunder Bay, Ontario. The other half of the core is retained for future assay verification, and/or metallurgical testing. Other QA/QC procedures include the insertion of blind blanks and standards for every tenth sample in the sample stream. Selected quarter core duplicates were assayed for 5% of the samples. The laboratory re-assays 10% of all samples (pulps and rejects) and additional checks are routinely run on anomalous values including gravimetric analysis and pulp metallics. Gold analysis is conducted by lead collection, fire assay with atomic absorption and/or gravimetric finish on a 30 gram sample. Check assays by a secondary lab are completed as necessary.Forward-looking StatementsThis release includes certain statements that may be deemed to be "forward-looking statements". All statements in this release, other than statements of historical facts, that address events or developments that management of the Company expect, are forward-looking statements. Actual results or developments may differ materially from those in forward-looking statements. Treasury Metals disclaims any intention or obligation to update or revise any forward-looking statements, whether as a result of new information, future events or otherwise, save and except as may be required by applicable securities laws. SOURCE: Treasury Metals Inc.For further information: Greg Ferron Vice President, Corporate Development T: 1.416.214.4654 Martin Walter President & CEO T: 1.416.214.4654